Request a Stainless Steel Gate Quote | Techno Kol Uzi

t271-41

To get a stainless steel gate quote, send us photos of the opening and a few details about the gate you want, such as width, style and use. We then measure on site, prepare a drawing and written specification for your approval, and manufacture the gate in our Tel Aviv workshop before installation.

Why choose stainless steel for a gate

Stainless steel is a strong choice for gates that face weather, salt air and daily use. It resists rust far better than untreated iron, keeps a clean, modern look over the years and needs little maintenance beyond occasional washing. For homes near the sea or in exposed yards, it is often the material that holds up best.

Because it is durable, stainless steel suits both pedestrian gates and larger driveway gates. The right grade and finish depend on how the gate will be used and where it will stand, which is something we review with you before production.

Choosing the grade and finish

Stainless steel comes in several grades, and the grade affects corrosion resistance and cost. For coastal or humid locations, a higher-resistance grade is usually recommended. The finish also changes the look: brushed, satin or polished surfaces each hide fingerprints and marks differently.

Brushed finish for a subtle, everyday look
Polished finish for a bright, decorative effect
Combined designs with steel or aluminum frames

Design and size details that affect the quote

The quote depends on the gate's width and height, the number of leaves, the infill pattern and whether it swings or slides. Solid panels, vertical bars and mesh each change the weight and the amount of material needed. Hinges, locks and the posts they attach to also matter, so we check the existing structure during the site visit.

Sending clear photos and rough measurements at the start helps us prepare a more accurate quote and avoids surprises later.

How the quote process works

Your request starts with photos of the opening and a short description of what you need. We then arrange an on-site measurement to confirm dimensions, ground conditions and fixing points. Based on that visit we prepare a drawing and a written specification covering materials, finish and fittings.

Once you approve the drawing and specification, we move to production in our factory. Nothing is manufactured until you have reviewed and accepted the details in writing.

Manufacturing and installation

Our factory has operated since 1945 and is run by the third generation of the family. Each gate is cut, welded and finished to the approved specification. Where appropriate, we apply hot-dip galvanizing or powder coating to protect the metal and extend its life.

After finishing, the gate is installed on site. We check alignment, swing or slide movement, and the operation of hardware before handover.

Safety and standards to keep in mind

Gates should move smoothly, close securely and be fixed to a solid structure. For railings and similar elements, Israeli standard SI 1142 is a useful reference point. Exact dimensional requirements, such as clearances and load values, are confirmed with your engineer or architect for your specific project rather than assumed.

Tell us early if the gate is for a building committee or a contractor project, since they may need documentation as part of their approval process.

Frequently asked questions

What information do I need to send for a stainless steel gate quote?

Send photos of the opening from the front and side, the approximate width and height, and a note on whether you want a swing or sliding gate. Any design ideas or reference images are also helpful.

Is a site visit needed before the quote?

In most cases yes, because we confirm exact measurements, ground conditions and fixing points on site. This gives you a more accurate drawing and specification to approve.

Which stainless steel finish is best for a gate?

A brushed finish is a practical everyday choice, while a polished finish gives a brighter, more decorative look. The best option depends on the look you want and how exposed the gate is to weather.

Do you manufacture in your own factory?

Yes, all gates are made in our factory at 37 Rival Street in Tel Aviv, then installed on site after your approval.

Common mistakes to avoid

Many buyers request a quote with only a rough idea of the size or finish, which leads to revisions later. Confirming measurements on site and approving a written specification before production avoids most delays.

Our recommendation

Decide on the grade and finish early, since they affect both durability and appearance, and ask for the drawing and specification in writing before approving the order.

Summary

A good stainless steel gate quote starts with clear photos and measurements, followed by a site visit, a written specification and your approval before manufacturing.

השאירו פרטים ונחזור אליכם